With Windows 8 and Windows 10 ( 64-bit ), Microsoft included Driver Signature enforcement feature to ensure that users of Microsoft can only load drivers that have been signed by Microsoft. Digital Signatures ensure that the software publisher or hardware vendor is trusted and verified by Microsoft. But some publishers and vendors cannot always pay Microsoft to verify all their products or Microsoft cannot verify all the drivers or programs that are published every day. For instance, when you want to use some less official drivers, old unsigned drivers or drivers developed by yourself, this feature needs to be disabled first before you can move on. This post we discuss different ways to disable Driver Signature enforcement on. Post Contents:-. Disable Driver Signature Enforcement The drivers you normally install on your computer from Windows Update, Original Equipment Manufacturers or some 3th-party driver download software, etc.
Procedure to permanently disable driver signature enforcement in windows 10 is quite similar to that of windows 8 and 8.1, but totally different from that of windows 7. Open the Settings app by navigating to the Start menu or Action center and click on Settings or All settings respectively. How to Disable Driver Signature Enforcement in Windows 10/8/7 64-Bit Open a Command Prompt with admin privileges. Type in the following command and press Enter. Close the Command Prompt and restart your computer.
Must be digitally verified by Microsoft via a digital signature. It is an electronic security mark that certifies the publisher for the driver, as well as all the relevant information related to it.
If a driver isn’t certified by Microsoft, Window won’t run them on either 32-bit or 64-bit system. This is referred to as “driver signature enforcement”. In order to install an unsigned driver, you need to disable driver signature enforcement. NOTE: Please be aware that disabling this, feature and using or installing the driver that was not officially signed could cause damage to your PC. Please only do so when you fully understand what you are about to do.
Disable Driver Signature from Startup settings This is the simplest way to disable driver signature enforcement on Windows 10, but bear in mind that this method will only disable driver signature temporarily. After you restart your computer driver signature enforcement will automatically turn itself on. To disable driver signature enforcement do the following: Click on start menu - settings - update & Security - Recovery. Then Click on Restart now under Advanced Startup As show bellow image. Advanced startup options Now click on Troubleshoot Advanced options Startup Settings and click the Restart button. When your computer restarts you’ll see a list of options. Here press F7 key to Disable The Driver Signature enforcement. Disable Driver Signature Enforcement If after installing new hardware device or third-party application you are getting The Digital Signature For This File Couldn’t Be Verified Error at startup unable to start windows normally and looking for disable Driver Signature that causes you need to boot from installation media To.
When you get the installation screen skip the first screen and on next screen click repair your computer. Now Troubleshoot Advanced options Startup Settings and click the Restart button. When your computer restarts you’ll see a list of options. Here press F7 key to Disable The Driver Signature enforcement. Enable Test Signing Mode Also, you Can Enable The Test Signing mode By performing Bellow command Which Allows to install or use the driver you want. To do this simply Open command prompt As Administrator Then Perform command Bellow one by one.
Bcdedit.exe -set loadoptions DISABLEINTEGRITYCHECKS bcdedit /set testsinging on Enable Test Signing Mode Then Restart your computer to enter test mode. You will be able to see the watermark saying Test Mode on the bottom right corner of your desktop. Now you can install or use the driver you want. Again If you want to leave Test Mode, Then again open the command prompt as administrator and perform command below. Bcdedit -set loadoptions ENABLEINTEGRITYCHECKS bcedit /set testingsigning off leave Test Mode Then restart your computer into normal mode. Permanently Disable driver signature enforcement.
The previous solution will only disable driver signature enforcement temporarily, but if you want to disable it permanently, follow these steps: First, open command prompt as administrator Then type command below and hit the enter key to execute the command. Bcdedit.exe /set nointegritychecks on command to disable driver signature enforcement Again If you Decide To enable driver signature enforcement back again, open the Command Prompt as administrator and perform Command bellow. Bcdedit.exe /set nointegritychecks off Enable driver signature enforcement Note: Driver Signing is a security feature that protects your system and you should consider re-enabling it as soon as it is possible.
Driver signature enforcement is a useful feature that provides extra protection. But sometimes extra protection can cause problems when installing certain drivers. We hope that you now understand how driver signature enforcement works and how to disable it in Windows 10.
Still, have any query, suggestion about this post feel free to discuss on comments below.
I see some related questions, but none have a solution for me. My problem is that I need to install a certain driver for a monitor. Windows 10 sees the monitor as a generic monitor, and will not show the proper resolutions. I have the driver for windows 8, but on 10 it says it 'does not contain digital signature information'. I have tried disabling this through cmd with both 'bdedit.exe /set nointegritychecks on' and 'bcdedit.exe /set testsigning on'. The first says it was successful. The other says the value is protected by Secure Boot policy and cannot be modified or deleted.
I tried restarting the pc to get the Startup Settings, but the moment that is chosen and the pc restarts, it goes straight back to the windows booting, the screen where you can choose to disable the digital signature (which apparently is f7 from the list I saw somewhere) does not appear. I am really at a loss here. Hello Leandro, Thank you for posting your query in Microsoft Community Forums. We are glad to help you.
When you tell certain driver, which driver are you referring to? If you are referring to display driver, then I suggest you to run “Hardware and Devices” troubleshooter to diagnose the exact issue.
Follow these steps to run the troubleshooter:. Press “ Windows key + X”.
Type “Troubleshooting” without quotes in the Search box and hit enter. Select “Hardware and Sound” from the Troubleshooter Window. Select “Hardware and Devices” under Devices option. Follow the On Screen instructions.
Method 2: Update the latest display drivers and check if that helps: Follow these steps:. Press “Windows Key + X” from the keyboard. Type “device Manager” without quotes in the search box and hit enter. Right click on the display drivers and select “Update”.
If the issue persists, uninstall and reinstall the latest display drivers from the manufacturer’s website. Hope this information helps. Feel free to get back to us for further queries.
We will be happy to assist you. Thanks and regards, Jenith. Thanks for the reply. Drivers wouldn't update, since Windows doesn't let it, with it not being digitally signed. I somehow got it to show the Startup Settings. It wasn't showing when I used the monitor I was reffering to. Had to plug in the TV.
Then the options showed (including the one to disable the Digital Signature checker). Since nothing happened, even after the driver was installed (i.e. I still couldn't choose resolutions), I tried the hardware troubleshooting.
When I start it, the monitor restarts, as if the HDMI was unplugged. It shows the following screen after that: However, I still cannot choose resolutions. And when I try the troubleshooter again, the same thing happens, the same 'problem' is found, and 'fixed'. I heard that disabling the Digital Signature checking through the startup settings is just a temporary measure, and that everytime you restart you have to do that, so is that what is messing things up, and even though device manager now shows the proper name for the monitor (not just generic monitor), it's still seeing it as generic? I contacted the store that sold me the monitor, and I was told the only problem was the driver. Also, now I see that it was, in fact, temporary.
After I thought the driver was properly installed, I went to Device Manager, and asked to update the monitor driver. The driver was 'updated', and the monitor went from being recognized as the monitor it is (with the philips name and everything), back to 'Generic non-pnp monitor'. I really want to solve this permanently. Is there a way to permanently disable the Digital Signature checks?
Like I said, I had tried the cmd commands, but no luck. Secure Boot won't let me.